補強の開発長は、構造コンクリート設計の重要なパラメーターです, 補強棒がコンクリートと鋼の間に適切にストレスを伝達できるようにすることを保証する. セクション 13 ASの 3600 (2018) 開発長を計算するための要件と方法論を提供して、強化の適切な固定を実現する. これにより、構造的完全性が保証されます, 安全性, さまざまな負荷条件下での保守性. 開発の長さは、バーサイズの影響を受けます, コンクリートの強度, 結合条件, カバー, 間隔, そして、バーが緊張しているのか圧縮されているのか. この規定は、ストレートバーの基本開発長をカバーしています, エポキシコーティングの調整, 閉じ込め効果, バーがフックまたはバンドルされている条件.
最新のSkyciv Foundation Design Updateは標準的なフック補強をサポートしています, 正確な開発長チェックを有効にします. ユーザーはフーチングバーの終わりをストレートバーとしてカスタマイズできるようになりました, cogs, または180°フック, さまざまな設計ニーズに柔軟性を確保します. This guide outlines the step-by-step process for determining the required development length for pad footings following AS 3600 セクション 13, コード要件に準拠するための関連する変更係数を検討します.
SkyCivのFoundationDesignソフトウェアを試してみたい? 当社の無料ツールを使用すると、ユーザーは次のことを実行できます。 コンクリート基礎の計算 何もダウンロードしたりインストールしたりせずに!
Starter Bar Development Length Check
Following AS 3600 (2018) セクション 13.1.5.1, the development length of starter bars is the minimum embedment required to ensure adequate reinforcement anchorage into concrete. This is critical for transferring stress between the bar and the surrounding concrete to prevent bond failure. The required length is calculated based on bar diameter, コンクリートの強度, and bond conditions, ensuring structural integrity under service and ultimate loads.
セクション 13.1.5.1: Development length of deformed bars in compression (l彼の,cb)
Basic development length:
f彼の =鉄筋降伏強度 (MPa)
fc‘ =コンクリート強度
db = Starter bar diameter (んん)
SkyCIV Foundation Designモジュールは、各負荷の組み合わせをチェックして、列が引張力にさらされているかどうかを判断します. もしそうなら, 必要な開発長を次のセクションに計算します 13.1.2 (Development length for a deformed bar in tension). この計算の簡単な説明は、ガイドの後半で提供されています.
必要な足場の厚さ (D必須)
The thickness of the footing should be greater than or equal to the calculated required embedment of the starter bars. 最小のフーチングの厚さは、方程式を使用してチェックされます 3 そして 4.
\(D_{必須} =カバー + d_{b,バツ} + d_{b,と} + d_{b, スターター} + l_{彼の} \) (Eq. 3)
\(D_{req'd} \leqt ) (Eq. 4)
どこ:
T =足場の厚さ (んん)
カバー=ボトムコンクリートカバー (んん)
db,バツ, db,と = X方向とZ方向のフーチングバーのサイズ (んん)
db,スターター= Starter bar size (んん)
l彼の =圧縮または張力に必要な開発長 (んん)
開発長の補強材のチェック
The SkyCiv Foundation Design module allows users to specify bar end configurations as straight. 90° cog or 180° hooked bars.
足場の強化に必要な開発長を計算すると、足場の寸法に直接影響します, 彼らが緊張力に対する強化を固定するのに十分であることを保証する. セクション 13.1.2 足場の強化の必要な開発長を決定するためのガイドを提供します.
Basic development length:
k1 = 1.3 for rebar with more than 300 mm concrete cast below the bar (1.0 さもないと)
k2 = (132 – db)/100
k3 = 1-[0.15(cd – db)/db]
cd =最小バークリア距離 (んん)
Straight bar:
90° cog or 180° hooked bar:
セクション 13.1.2.2 also specifies that the value of l彼の,t calculated as above shall be multiplied by the following:
- Multiplied by 1.5 for epoxy-coated bars
- Multiplied by 1.3 when lightweight concrete is used
- Multiplied by 1.5 & 1.3 for both epoxy-coated bars and lightweight concrete is used
提供されるアンカレッジ長
\(l_{提供された} \L_を取得する{彼の,t}\) (Eq. 8)
ディテールチェック: 足場の厚さの検証 (t):
SkyCIV Foundation Designモジュールは、BARの構成とコンクリートカバーに基づいて、足場の厚さが適切かどうかをチェックします. 不十分である場合、またはバーが突き出ている場合, 設計の失敗ではなく警告を発します. このモジュールは、上層と下層の両方で縦方向および横方向の補強材の両端にある足場の厚さを評価します. The minimum pin diameter (D) shall be based on the provision specified by AS 3600 セクション 17.2.3.3
\(\左(\テキスト{h + カバー}\正しい) \leqt ) (Eq. 9)
SkyCivのFoundationDesignソフトウェアを試してみたい? 当社の無料ツールを使用すると、ユーザーは次のことを実行できます。 コンクリート基礎の計算 何もダウンロードしたりインストールしたりせずに!
製品開発者
BSc (民事), 修士課程 (民事)