AS / NZSでのSkyCivロードジェネレーターの使用 1170.3 積雪荷重の計算
SkyCiv LoadGeneratorを使用して構造物の積雪圧力を計算するには, プロセスは、最初にコード参照を定義することです. そこから, ワークフローは、[プロジェクト]タブでパラメータを定義することです, [サイト]タブ, および[建物]タブ, それぞれ. しかしながら, この計算を使用できるのは、Professionalアカウントを持っているユーザー、またはスタンドアロンのLoadGeneratorモジュールを購入したユーザーのみです。. これからスタンドアロンモジュールを購入できます リンク.
サイトデータ
Using the AS/NZS 1170 積雪量計算, you need to define the Annual Recurrence Interval or the SLS/ULS parameters. After selecting the options for these parameters, you need to put the address of the structure. The corresponding snow load for the address will be automatically calculated. Take note that this value is based on the following:
- セクション 2 AS / NZSの 1170.3 for classification of snow regions based on Figures 2.1 そして 2.2 and based on elevation
- テーブル 5.2 for specific locations in Australia
Take note that the snow region classification automatically displayed in the module shall prioritize the classification of the area based on elevation. To display the snow region map based on Figures 2,1 そして 2.2, クリックする必要があります “地図の等高線を表示” 次に、 “雪” – “Australia/New Zealand.” For Australian locations indicated in Table 5.2, the user should select “Terrain Classification for Snow” AS/NZS で指定されたとおり 1170.3 サップ 1.

構造データ
構造データと風雪パラメータは異なるアコーディオンに分けられます. 積雪荷重を計算するために, 積雪荷重チェックボックスをオンにする必要があります.

Snow Exposure Category
This parameter is used in getting Exposure Reduction Coefficient Ce. 各オプションの定義は、以下の表で定義されています。:
ばく露カテゴリー | 定義 |
---|---|
Sub-alpine | Sites classified as sub-alpine region. |
保護された | Sites where roof is protected from the wind by obstructions such as other structures, terrain features or numbers of closely spaced trees higher than the roof. |
Semisheltered | Sites where roof is only partially protected by numbers of scattered obstructions higher than the roof (例えば, scattered trees). |
吹きさらし | Sites where the roof is exposed on all sides, with no protection provided by obstructions, trees, or terrain features higher than the roof. |
不均衡/漂流雪荷重ケースを検討してください?
このパラメータは、不均衡な積雪荷重の場合を計算するための「はい」または「いいえ」です。. 「いいえ,」バランスの取れた積雪荷重の場合のみ計算されます. 一方, 「はい」を選択すると,」不均衡な積雪荷重ケースの表には、. There are four options for AS/NZS 1170.3 alpine region:
デュオピッチの屋根に漂う
このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます:

このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます
このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます:

Drift on lower roof
This case is used to calculate the snow load drift on lower roof level.

このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます
このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます, このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます, このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます, 等.

一方, AS/NZS にはさらに 2 つのオプションがあります 1170.3 亜高山帯:
Drift on obstructed roof with parapet
This case is used to calculate the snow load drift on parapet walls in sub-alpine region.

Drift on obstructed roof with abutting
This case is used to calculate the snow load drift on obstructed roof with abutting in sub-alpine region.

結果
The snow load results will show the parameters in calculating the undrifted snow load for either alpine or sub-alpine region as shown below:

Drifted/Unbalanced Snow Load
不均衡/漂流雪荷重が考慮されるように選択されている場合, 結果は、定義されたケースに応じて表にまとめられます:


詳細な計算
詳細な積雪荷重の計算には、次のユーザーのみがアクセスできます。 プロフェッショナルアカウントユーザー と購入した人 スタンドアロンの負荷ジェネレータモジュール. 計算に使用されるすべてのパラメーターと仮定は、ユーザーに透過的にするためにレポートに表示されます. あなたはこれを通してサンプルの詳細な計算をダウンロードすることができます リンク.
