SkyCivドキュメント

SkyCivソフトウェアのガイド - チュートリアル, ハウツーガイドと技術記事

SkyCiv Load Generator

  1. ホーム
  2. SkyCiv Load Generator
  3. スノーロード
  4. NBCC 2015 積雪荷重の計算

NBCC 2015 積雪荷重の計算

NBCCでのSkyCivロードジェネレーターの使用 2015 積雪荷重の計算

SkyCiv LoadGeneratorを使用して構造物の積雪圧力を計算するには, プロセスは、最初にコード参照を定義することです. そこから, ワークフローは、[プロジェクト]タブでパラメータを定義することです, [サイト]タブ, および[建物]タブ, それぞれ. しかしながら, この計算を使用できるのは、Professionalアカウントを持っているユーザー、またはスタンドアロンのLoadGeneratorモジュールを購入したユーザーのみです。. これからスタンドアロンモジュールを購入できます リンク.

サイトデータ

NBCCの使用 2015, you need to select Recurrence Interval, 限界状態, and Importance Category parameters first before putting an address the Project Address input. The module will search for the location based on Table C-2 of Appendix C (NBCC 2015).

NBCC 2015 snow load data
図 1. SkyCiv LoadGeneratorの[サイト]タブ

You can manually put the ground snow load and the associated rain load whenever needed. しかも, Area Classification should be defined in order to calculate for Cw.

NBCC 2015 snow load topo parameter
図 2. Additional snow load site parameter on SkyCiv Load Generator NBCC 2015 計算.

構造データ

構造データと風雪パラメータは異なるアコーディオンに分けられます. 積雪荷重を計算するために, 積雪荷重チェックボックスをオンにする必要があります.

NBCC 2015 snow load parameters
図 3. Snow load parameters for building tab in SkyCiv Load Generator module.

傾斜した屋根の状態

This parameter is used in calculating Slope Factor, Cs. The options for this parameter are Unobstructed slipperyそして Other Cases

不均衡/漂流雪荷重ケースを検討してください?

このパラメータは “はい” または “番号” to calculate for the Unbalanced Snow Load Case. 選択すると “番号,” バランスの取れた積雪荷重の場合のみ計算されます. 一方, 選択すると “はい,” 不均衡な積雪荷重ケーステーブルは次のように表示されます. There are five options for NBCC 2015:

マルチレベルの屋根 – 場合 1

This case is used in calculating snow load drift on lower roofs where the wind source is coming from the upper roof as shown in the figure below based on Figure 4.1.6.5-A and 4.1.6.5-B Case I of NBCC 2015.

NBCC 2015 drifted snow load case  multi-level roof case 1
図 4. Snow load parameters in solving snow drift for Multi-level roof case 1.

マルチレベルの屋根 – 場合 2

Similar to the previous case, this is used in calculating snow load drift on lower roofs where the wind source is coming from the lower roof as shown in figure below based on Figure 4.1.6.5-A and 4.1.6.5-B Case II of NBCC 2015.

NBCC 2015 drifted snow load case  multi-level roof case 2
図 5. Snow load parameters in solving snow drift for Multi-level roof case 2.

マルチレベルの屋根 – 場合 3

This case is used in calculating snow load drift on lower roofs where the wind source is coming from the lower roof in a diagonal direction as shown in the figure below based on Figure 4.1.6.5-A and 4.1.6.5-B Case III of NBCC 2015.

NBCC 2015 drifted snow load case  multi-level roof case 3
図 6. Snow load parameters in solving snow drift for Multi-level roof case 3.

Areas Adjacent to Roof Projections

This case is used in calculating snow drifts on areas adjacent to roof projections such as parapets, このケースは、以下に示すように、デュオピッチ/切妻屋根の漂流雪荷重を計算するために使用されます, 等.

NBCC 2015 drifted snow load case on obstructions or projections
図 7. Snow load parameters in solving snow drift on areas adjacent to roof projections.

Gable Roofs

このケースは、対称切妻屋根の積雪荷重ドリフトを計算するために使用されます.

NBCC 2015 drifted snow load case on gable roof
図 8. Snow load parameters in solving snow drift on gable roofs.

結果

積雪荷重の結果は、以下に示すように、平衡積雪荷重を計算する際のパラメータを示します。:

NBCC 2015 snow load undrifted case and parameters
図 9. Snow load parameters used in the calculation and the calculated balanced snow load.

不均衡な積雪荷重

不均衡/漂流雪荷重が考慮されるように選択されている場合, 結果は、定義されたケースに応じて表にまとめられます (sample below):

Unbalanced cases results
図 10. Sample results for unbalanced snow load on multi-level roofs and areas adjacent to roof projections.
Unbalanced cases results
図 11. Sample results for unbalanced snow load on gable roofs.

詳細な計算

詳細な積雪荷重の計算には、次のユーザーのみがアクセスできます。 プロフェッショナルアカウントユーザー と購入した人 スタンドアロンの負荷ジェネレータモジュール. 計算に使用されるすべてのパラメーターと仮定は、ユーザーに透過的にするためにレポートに表示されます. あなたはこれを通してサンプルの詳細な計算をダウンロードすることができます リンク.

Detailed snow load calculation report

追加のリソースについて, これらのリンクを参照用に使用できます:

 

この記事は役に立ちましたか?
はい 番号

どのように我々は助けることができます?

トップへ戻る