Di seguito è riportato un elenco di codici di errore e le loro possibili cause. Questi errori verranno visualizzati nel nostro software FEA quando un utente tenta di risolvere una struttura irrisolvibile. Di seguito è riportata una tabella che mostra le possibili cause e soluzioni a tali problemi:
Codice di errore | Messaggio | Possibili problemi | Possibili soluzioni |
---|---|---|---|
1 | Fuori tempo – Server non disponibile. |
|
|
2 | Fuori tempo – La soluzione ha richiesto troppo tempo. |
|
|
3 | Errore del server |
|
|
101 | Accesso non autorizzato |
|
|
102 | Per favore aggiungi un membro |
|
|
103 | Si prega di aggiungere un carico |
|
|
104 | Si prega di aggiungere un supporto |
|
|
105 | Si prega di aggiungere una sezione |
|
|
106 – 109, 116, 117 | (*Nome attributo*) di sezione ## non può essere zero |
|
|
110 | La struttura non è vincolata |
|
|
111 | Please remove disconnected Node # X |
|
|
112 | Si prega di rimuovere l'elemento disconnesso (Membro) # X |
|
|
113 | La struttura non è vincolata |
|
|
114, 115, 118 | Risolvi errore |
|
|
119 | Struttura del traliccio non stabile (Solo traliccio SkyCiv) |
|
|
181 | Member ID cannot be used for a support since it is the slave node (nodo B) of the rigid link. |
|
|
182 | Node #ID is the master node (nodo A) of Member #ID rigid link and cannot be used as the slave node (nodo B) of another rigid link member. |
|
|
183 | Node #ID is the slave node of Member #ID but it is already used as a slave in another rigid link member. A slave node cannot be constrained to more than one master node. |
|
|
300, 301 | L'analisi statica non lineare non è riuscita a convergere |
|
|
302 | L'analisi di instabilità non è stata eseguita |
|
|
303 | Impossibile eseguire l'analisi della frequenza dinamica |
|
|
304, 305 | Impossibile eseguire l'analisi dello spettro di risposta |
|
List of Warnings
Below are a list of warning messages that may not cause the solver to error, but could be adjustments or comments from the solving process:
Messaggio | Dettagli |
---|---|
Continuous Member x has a problem with straightness as its internal members are using different local axes. Please check the nodes along this member form a straight line |
|
Load Combo y: Membro(S) x were removed from the model during the tension/compression only analysis over 1 iterazioni. | This is a warning regarding the iterative analysis when the model contains tension or compression members. The iterative analysis will remove compression members that are in tension (e viceversa). It will resolve, however in each iteration it checks if removed tension-members may have possibly reversed back to tension and compression-members have reversed back to compression. If the member gets removed and re-added from the model too many times (vale a dire. it reversed too much) then it just gets permanently removed as it’s deemed problematic for the iterative analysis to complete. |
Node x has been removed from the model because it is not used in any members or plates. | Solver detected an unused node and removed it during the analysis process |
Support #x for Node #y was ignored because the node was unused or does not exist. | Solver detected an unused support and removed it during the analysis process |
Load Combo #x: 1 iterations and y% convergence error | During a non-linear analysis the results will try to converge to a certain percentage (this can be adjusted in the software settings). This message is just notifying the user of that convergence error. |