SkyCiv文档

您的SkyCiv软件指南 - 教程, 使用指南和技术文章

SkyCiv结构3D

  1. SkyCiv结构3D
  2. 解决
  3. 求解器错误和警告列表

求解器错误和警告列表

以下是错误代码及其可能原因的列表. 当用户尝试解决无法解决的结构时,这些错误将显示在我们的 FEA 软件中. 下表显示了此类问题的可能原因和解决方案:

错误代码 信息 可能的问题 可能的解决方案
1 时间到 – 服务器无法使用.
  • 互联网已断开连接或掉线
  • 连接到SkyCiv服务器的问题.
2 时间到 – 解决方案花了太长时间.
  • 成员或节点断开连接, 导致求解器失败
  • 模型太大,无法求解 (通常 > 20,000 成员或 > 10,000 盘子)
  • 在设置中增加求解器超时 > 解决 > 求解器超时
  • 运行修复模型 (高级 > 模型维修) 查找模型问题
  • 删除部分模型并解决尝试定位错误源
  • 打开每个元素的数据表, 并检查输入中是否有任何缺失/不正确的数据
  • 减小模型的大小并再次尝试求解
  • 如果问题仍然存在,请联系 [email protected]
3 服务器错误
  • 连接到SkyCiv服务器的问题.
101 越权存取
  • 授权或访问存在问题
102 请添加会员
  • 没有成员
103 请添加负载
  • 没有负载 (军队) 应用于结构
  • 添加点荷载, 分散负荷, 片刻, 或面积负荷
  • 开启自重
104 请添加支持
  • 没有支持来约束您的模型
105 请添加一个部分
  • 尚未为成员定义节
106 – 109, 116, 117 (*属性名称*) 的部分 ## 不能为零
  • 节属性缺少数据
  • 旧数据
  • 打开相关部分并查看输入, 寻找丢失的数据, 0, 或输入错误
  • 删除相关部分,然后重新输入并重新提交数据
110 结构不受限制
  • 结构不是静态的
  • 该结构在一个或多个自由度上不受约束
  • 支撑不足或支撑内的固定性
  • 添加更多支撑,看看结构是否解决. 如果有, 可能没有足够的支持来约束模型, 它不是静态的.
  • 将您的支持更改为所有固定 (FFFFFF) 看看结构是否解决. 如果有, 可能没有足够的固定 ('F') 自由程度 (添加更多F)
111 请删除断开连接的节点 # X
  • 节点编号 X 浮动并且没有连接任何东西
  • 将板或构件连接到节点 – 删除节点
112 请删除断开连接的元素 (会员) # X
  • 元素编号 X 浮动且未连接到结构的其余部分
  • 通过节点将元素连接到结构的其余部分
  • 删除元素
113 结构不受限制
  • 结构在某些平移方向上完全不受约束 (X, Y或Z)
114, 115, 118 解决错误
  • 解决期间出现问题. 模型或输入可能有问题
  • 运行修复模型 (高级 > 模型维修) 查找模型问题
  • 检查所有断开的节点, 元素或板. 检查以确保整个模型通过节点连接.
  • 如果您的模型有多个板, 尝试故障排除 一次将所有盘子啮合 以确保正确的连接.
  • 删除模型的某些部分,并尝试查找错误源
  • 打开每个元素的数据表, 并检查输入中是否有任何缺失/不正确的数据
  • 观看下面的视频 6 对模型进行故障排除的提示
119 桁架结构不稳定
(仅SkyCiv桁架)
  • 该模型可能是不稳定的桁架结构
  • 添加更多的构件或支撑以稳定桁架
  • 记住每个成员都固定在末端,因此结构必须为三角形才能稳定.
181 Member ID cannot be used for a support since it is the slave node (节点B) of the rigid link.
  • Support connected to a slave node of a rigid link/diaphragm
  • Rigid Diaphragms create dummy rigid links, so if you can’t find that particular rigid link member in your model, this is probably why
  • Flip the direction of your rigid link member, so the master node is connected to the support
  • Change the rigid link member to a regular normal/continuous member
  • Remove any offsets of members connected to supports
  • Help Video
182 Node #ID is the master node (节点A) of Member #ID rigid link and cannot be used as the slave node (节点B) of another rigid link member.
  • Two rigid members connected to another
  • Replace one of the rigid members with a normal or continuous member
  • Help Video
183 Node #ID is the slave node of Member #ID but it is already used as a slave in another rigid link member. A slave node cannot be constrained to more than one master node.
  • Two rigid links with a common slave node
  • Rigid Diaphragms create dummy rigid links, so if you can’t find that particular rigid link member in your model, this is probably why
  • Try change the direction of the member (switching the slave node -> master node)
  • Try remove any offsets on the member if they exist
  • If you have connected rigid diaphragms, merge the plates into a single plate
  • Help Video
300, 301 非线性静态分析无法收敛
  • 结构可能不稳定, 没有足够的约束或支持
  • 结构可能会弯曲
  • 如果模型中存在电缆: 电缆可能会导致模型无法收敛
  • 增加设置中的收敛容限 > 解决 > 收敛容差 – 为您的结构添加更多支撑
  • 尝试运行线性静态 + 屈曲分析,检查结构是否屈曲
  • 增大节的大小以确定结构是否屈曲
  • Try turn on Advanced -> Solver -> Auto-Stabilize in your settings
  • 如果模型中存在电缆: 试试这些 电缆提示 让你的模型解决.
302 屈曲分析无法运行
  • 结构可能不稳定, 没有足够的约束或支持
  • 尝试为您的模型添加更多约束 (将成员端固定性更改为 FFFFFF)
303 动态频率分析无法运行
  • 结构可能不稳定
  • Try turn on Advanced -> Solver -> Auto-Stabilize in your settings
304, 305 响应谱分析未能运行
  • 结构可能不稳定或动态频率分析可能失败, 这使得响应谱分析无法完成.

List of Warnings

Below are a list of warning messages that may not cause the solver to error, but could be adjustments or comments from the solving process:

信息 细节
Continuous Member x has a problem with straightness as its internal members are using different local axes. Please check the nodes along this member form a straight line

 

Load Combo y: 会员(s) x were removed from the model during the tension/compression only analysis over 1 迭代. This is a warning regarding the iterative analysis when the model contains tension or compression members. The iterative analysis will remove compression members that are in tension (反之亦然). It will resolve, however in each iteration it checks if removed tension-members may have possibly reversed back to tension and compression-members have reversed back to compression. If the member gets removed and re-added from the model too many times (即. it reversed too much) then it just gets permanently removed as it’s deemed problematic for the iterative analysis to complete.
Node x has been removed from the model because it is not used in any members or plates. Solver detected an unused node and removed it during the analysis process
Support #x for Node #y was ignored because the node was unused or does not exist. Solver detected an unused support and removed it during the analysis process
Load Combo #x: 1 iterations and y% convergence error During a non-linear analysis the results will try to converge to a certain percentage (this can be adjusted in the software settings). This message is just notifying the user of that convergence error.

6 尝试对结构模型进行故障排除的技巧或提示



本文对您有帮助吗??
是的 没有

我们能帮你什么吗?

回到顶部