NS Create Point tool places individual coordinate points on the canvas. Points act as precise anchors that other geometry can snap to, and are useful as reference markers in structural drawings.

Step-by-step

1. 1Tıklayın Create Point in the toolbar (or press P) to activate point-creation mode.
2. 2Click anywhere on the canvas to place a point at that location.
3. 3Alternatif olarak, type coordinates in X,Y biçim (Örneğin. 100,200) ve bas seçin.
4. 4Continue clicking or typing coordinates to place additional points in the same session.
5. 5Basın ESC to exit point-creation mode.

NS Create Line tool draws individual straight line segments. Each click-pair defines one line. This is the most fundamental drawing tool in SkyCiv CAD and is used extensively in structural and architectural drawings.

Step-by-step

1. 1Tıklayın Create Line (or press L) to activate line-creation mode.
2. 2Click on the canvas to set the start point.
3. 3Move the mouse — a live preview of the line follows the cursor.
4. 4Click to set the end point, or type a length value and press seçin for a precise distance.
5. 5Basın ESC to exit.

NS Create Polyline tool draws a continuous chain of line segments stored as a single object. Polylines are ideal for outlines in structural drawings where all segments must remain joined. This tool is in a dropdown group — click the arrow on the toolbar button to reveal the Create Spline variant.

Step-by-step

1. 1Tıklayın Create Polyline (or press Ctrl+L) to activate polyline mode.
2. 2Click on the canvas to set the first vertex.
3. 3Continue clicking to add additional connected vertices — each click extends the polyline.
4. 4Basın ESC bitirmek için. The polyline is stored as a single continuous shape.

NS Create Spline tool draws smooth, continuously curved lines defined by a series of control points. Useful for organic curves, road alignments, or any geometry requiring smooth curvature. Found in the Polyline dropdown group.

Step-by-step

1. 1Expand the Polyline dropdown and click Create Spline (or press SP).
2. 2Click on the canvas to set the first control point.
3. 3Continue clicking to place additional control points — the curve updates live.
4. 4Basın ESC to finish the spline.

NS Create Arc tool draws a circular arc defined by two base points and a rise height — the perpendicular distance from the chord midpoint to the arc peak. Commonly used for curved beams, arched openings, and rounded structural elements.

Step-by-step

1. 1Tıklayın Create Arc (or press Bir) to activate arc mode.
2. 2Click on the canvas to set the first base point.
3. 3Type a chord length and press seçin, or click to set the second base point.
4. 4Type the rise height ve bas seçin, or move the mouse and click to set it visually.
5. 5The arc is created with the specified dimensions.

NS Create Rectangle tool draws an axis-aligned rectangle by defining two diagonally opposite corners. The result is a closed polyline with four right-angle corners — useful for floor plans, plate outlines, and structural cross-sections.

Step-by-step

1. 1Tıklayın Create Rectangle (or press R) to activate rectangle mode.
2. 2Click on the canvas to set the first corner.
3. 3Move the mouse — a live rectangle preview follows the cursor.
4. 4Click to set the opposite corner and complete the rectangle.

NS Create Circle toolbar button opens a dropdown group with three variants: standard circle, circle by 4 SkyCiv Bölüm Oluşturucu bir delik eklemenizi sağlar, ve n-polygon. The standard circle places a full 360° circle defined by a center point and radius.

Step-by-step

1. 1Tıklayın Create Circle (or press C).
2. 2Click on the canvas to set the center point.
3. 3Move the mouse outward to preview the radius.
4. 4Type a radius value and press seçin for an exact size, or click to confirm visually.

NS Create Circle by 4 Yaylar variant constructs a circle from four connected arc segments. Useful when downstream tools need to work with the circle as distinct arc entities rather than a single circular object. Found in the Daire dropdown group.

Step-by-step

1. 1Expand the Circle dropdown and click Create Circle by 4 Yaylar.
2. 2Click on the canvas to set the center point.
3. 3Move the mouse to preview the radius.
4. 4Type a radius value and press seçin, or click to confirm the size.
5. 5The resulting circle is composed of four arc segments joined at the cardinal points.

NS Create n-Polygon tool draws a regular polygon with any number of sides, placed by center point and circumscribed radius. Found in the Daire dropdown group. The resulting shape is stored as a closed polyline.

Step-by-step

1. 1Aç Şekiller panel and set the desired number of sides (varsayılan: 6).
2. 2Expand the Circle dropdown and click Create n-Polygon.
3. 3Click on the canvas to set the center point.
4. 4Move the mouse outward to preview the polygon size.
5. 5Type a radius value and press seçin, or click to confirm.

NS Create Hatch tool fills a closed boundary region with a repeating hatch pattern. Hatches are widely used in structural and architectural drawings to denote material sections — concrete, çelik, earth, ve dahası.

Step-by-step

1. 1Tıklayın Create Hatch (or press H) to activate hatch mode.
2. 2Click inside a closed boundary region on the canvas — the boundary is detected automatically.
3. 3The hatch pattern fills the detected region.

NS Relative Move tool translates selected objects by a displacement vector — pick a base point, then pick or type a destination to shift all selected objects by the same offset. Equivalent to AutoCAD’s MOVE command.

Step-by-step

1. 1Select the objects to move.
2. 2Tıklayın Relative Move (or press M).
3. 3Click anywhere on the canvas to set the base point of the move vector.
4. 4Move the mouse — a live preview shows the displaced objects.
5. 5Click to place, or type an exact distance and press seçin.

NS Döndür tool rotates selected objects about a chosen center point. Rotate by dragging interactively or type an exact angle in degrees. Equivalent to AutoCAD’s ROTATE command.

Step-by-step

1. 1Select the objects to rotate.
2. 2Tıklayın Döndür (or press Ctrl+R).
3. 3Click on the canvas to set the rotation center point.
4. 4Move the mouse to preview the rotation angle.
5. 5Click to confirm, or type an angle in degrees and press seçin.

Relative Rotate (Reference Rotate) lets you rotate a selection by specifying an existing itibaren direction and a new target yön. Ideal when you know a specific edge or line should align with a target angle or point — no manual angle arithmetic needed.

Step-by-step

1. 1Select the objects to rotate.
2. 2Tıklayın Relative Rotate in the Move dropdown.
3. 3Click to set the rotation center point.
4. 4Click a reference point to define the current (itibaren) yön.
5. 5Move the mouse — a preview shows the angle without yet rotating the objects.
6. 6Tıkla target point to complete the rotation, or type an angle and press seçin.

NS Hizala tool moves ve rotates a selection in a single operation by matching two source points on the selection to two destination points on the drawing. Particularly powerful for snapping components into place when you have two known reference locations.

Step-by-step

1. 1Select the objects to align.
2. 2Tıklayın Hizala in the Move dropdown.
3. 3Tıklayın source point 1 (on the selection), sonra destination point 1 (tuval üzerinde).
4. 4Tıklayın source point 2 (on the selection), then move to destination point 2.
5. 5Click to complete — the selection is simultaneously translated and rotated so both point pairs coincide.

NS Öğeleri bastırmak, üyeleri döndürmenin hızlı ve kolay bir yoludur tool reflects selected objects across a mirror axis defined by two points. The original objects are replaced by their mirrored counterparts. To keep the originals, kullanım Ayna Kopyalama yerine.

Step-by-step

1. 1Select the objects to mirror.
2. 2Tıklayın Öğeleri bastırmak, üyeleri döndürmenin hızlı ve kolay bir yoludur (or press MI) in the Move dropdown.
3. 3Click to set the start point of the mirror line.
4. 4Click to set the end point of the mirror line.
5. 5The selection is reflected across the defined axis.

NS Göreli Kopya tool duplicates selected objects and places the copy at an offset defined by picking a base point and a destination. The workflow is identical to Relative Move — but the originals stay in place.

Step-by-step

1. 1Select the objects to copy.
2. 2Tıklayın Göreli Kopya in the Copy dropdown.
3. 3Click anywhere on the canvas to set the base point.
4. 4Move the mouse — a live preview of the copy follows the cursor.
5. 5Click to place the copy, or type an exact distance and press seçin.

Ayna Kopyalama creates a reflected duplicate of selected objects across a user-defined axis, leaving the originals in place. Use this instead of Öğeleri bastırmak, üyeleri döndürmenin hızlı ve kolay bir yoludur when you need both the original and its reflection.

Step-by-step

1. 1Select the objects to mirror-copy.
2. 2Tıklayın Ayna Kopyalama (or press Ana farkın, kiriş flanşlarının destek kolonuna bağlantısında yattığını fark edebilirsiniz.) in the Copy dropdown.
3. 3Click to set the start point of the mirror line.
4. 4Click to set the end point of the mirror line.
5. 5A mirrored copy is created — the originals remain unchanged.

NS Diziyi Kopyala tool distributes multiple copies of selected objects along a vector direction. The number of copies and total span are configured in the Şekiller panel, making it ideal for regularly spaced structural elements such as columns, kafesler, and bolt groups.

Step-by-step

1. 1Select the objects to array.
2. 2Yı kur copy count ve span distance içinde Şekiller panel.
3. 3Tıklayın Diziyi Kopyala (or press AR) in the Copy dropdown.
4. 4Click to set the base point of the array.
5. 5Move the mouse to set the direction, then click to create the copies.

NS Ofset Kopyalama tool creates a parallel duplicate of selected lines or polylines at a specified perpendicular distance. Equivalent to AutoCAD’s OFFSET command — commonly used for wall thickness, lane markings, and parallel structural members.

Step-by-step

1. 1Select the lines or polylines to offset.
2. 2Enter the ofset mesafesi içinde Şekiller panel.
3. 3Tıklayın Ofset Kopyalama (or press Ö) in the Copy dropdown.
4. 4The offset copy is created parallel to the original at the specified distance.

NS Döndürerek Kopyala tool creates multiple copies of selected objects in a circular (polar) pattern around a center point. Useful for radially symmetric structures such as bolt groups on a flange or members in a circular truss.

Step-by-step

1. 1Select the objects to copy by rotation.
2. 2Yı kur copy count ve total rotation angle içinde Şekiller panel.
3. 3Tıklayın Döndürerek Kopyala in the Copy dropdown.
4. 4Click to set the rotation center point.
5. 5Move the mouse to preview, then click to create the copies.