Starting a design is quick. Zodra u de verbindingsontwerpmodule opent, a pop-up asks for the conditions that define your connection, and the cards below it filter down to the connections that match.
Hier, u moet de volgende informatie verstrekken::
- Ontwerpcode
- Eenheden
- Categorieën
- Soorten
- Oriëntatie
- De verbinding
Ontwerpcode
The design code is the standard your design checks are written against. Pick it first, because it drives everything after it: which checks run, de factoren van veiligheid, the design coefficients, and which categories and connection types are even offered.
The design codes SkyCiv Connection Design supports are:
Coverage is not equal between the two. AISC 360-16 covers every category and connection type below. ALS 4100:2020 covers shear connections framing W to W, and nothing else, so if you need a moment connection, a brace, a splice or an HSS column, choose AISC.
Eenheden
Mixing units is an easy way to get a wrong answer, and converting by hand between inches en millimeter, of kip en kN, wastes time you would rather spend on the design. So the module works in whichever system you picked and reports in the same one.
Onder AISC 360-16 you can choose Imperial or Metric. Onder AS 4100:2020 the unit selector is fixed to Metric, so you will not see the option.
Categorieën
The category describes what is connecting to what: the member framing in, and the support it frames into. A wide flange beam into a wide flange column is W to W.
The categories available are:
- W to W, wide flange to wide flange, covering beam to column and beam to beam
- HSS to W, a wide flange beam framing into a hollow section column
- Channel to Channel
- versteviging
- Las
W to W is the only category available under AS 4100:2020. The rest are AISC 360-16.
Soorten
The type groups connections by the load they are built to carry. All the shear connections sit together, all the moment connections in another set, enzovoorts. Here is what each type carries:
| Type | Axiaal | Schuintrekken | Moment |
| Afschuifverbindingen | X | ✅ | X |
| Schuintrekken + Axiale verbindingen | ✅ | ✅ | X |
| Momentverbindingen | ✅ | ✅ | ✅ |
| Brace-verbindingen | ✅ | X | X |
| Splice-verbindingen | ✅ | ✅ | ✅ |
Brace connections cover verticaal, chevron, knie, horizontal and truss braces. Splices cover kolomverbindingen en balkverbindingen.
Onder AS 4100:2020, shear is the only type offered.
Oriëntaties
The design checks do not stop at the beam and the connection components. The supporting member matters too, and where on that member you land changes the answer. Framing into a column flange puts the load into a different load path than framing into the web, and the local limit states of the support, such as web local yielding and local flange bending, often govern.
The orientations available are:
- Balk naar Kolom Flens
- Web van straal naar kolom
- Met de verbindingsontwerpmodule van SkyCiv kunt u verschillende ontwerpcontroleberekeningen voor stalen verbindingen uitvoeren, framing into the web of a supporting beam
- Straal naar HSS-kolom, to either the wide face or the narrow face
Which of these you see depends on the category and type you picked. A moment connection, bijvoorbeeld, is offered to the column flange and the column web but not beam to beam.
De verbinding
Once you have supplied the information above, the cards in the pop-up filter down to the connections available for that combination. Each card carries a sample image so you can check you are looking at the connection you had in mind before you commit to it. Click the one you want and the model opens, ready for sections and loads.
If you are not sure which configuration suits the job, de lijst met ondersteunde verbindingstypen sets out every option by code and category, als de gids voor verbindingsontwerp covers the workflow from here on.
Probeer het nu
The starter screen takes about thirty seconds to work through, en je kunt het doen zonder account. Pick a code, a category and a type, choose a connection, and see which checks run.
Aanmelden voor gratis account
Met een gratis account kunt u uw verbindingsbestanden opslaan en opnieuw laden, wat de gratis tool niet doet. Het geeft je ook toegang tot de rest van SkyCiv's structurele software, inclusief Structural 3D.
Verbindingsontwerp standalone
U wilt alleen de verbindingsontwerpmodule gebruiken? Klik op onderstaande knop voor de losse prijzen.
