Υπολογιστής σύνδεσης διάτμησης SkyCiv

The calculator sizes and checks a simple connection between steel members, the kind that delivers a beam end reaction into a column or a supporting beam. You choose the configuration, define the connecting element and the fasteners, then enter the design shear.

It reports a utilization ratio against each limit state rather than a single pass or fail, so you can see which check is close to governing and what to change if it is not.

A shear connection transfers vertical shear from one member to another, typically from a beam into a column. It is a simple connection: it is detailed to carry the end reaction and to rotate at the joint, not to carry end moment.

That rotation is the point. A moment connection has to be stiff enough to hold the beam end against rotation, which takes heavier plates, more welding and often column stiffeners. A shear connection is allowed to rotate, so it stays light and quick to fabricate, which is why it is the default choice wherever the frame gets its lateral stability from somewhere else.

The components depend on the configuration, but they generally include:

• Πλάκες: single or double plates bolted or welded to the beam and column.
• Γωνίες: single or double angles connecting the beam web to the support.
• End plates: plates welded to the beam end, then bolted to the column.
• Μπουλόνια: fasteners securing the plates or angles to the members.
• Συγκολλήσεις: used in place of bolts, most often on the supported side.
• Direct welds: joining the beam web straight to the column face.

Most configurations are welded on one side and bolted on the other. The weld is made in the shop, where access and position are controlled, and the bolts are left for the field, where the erector needs something quick to make and a little tolerance to work with.

Shear connections appear wherever a beam frames into a support and the frame gets its lateral resistance elsewhere, from bracing or a core. Οι κοινές εφαρμογές περιλαμβάνουν:

• Κουφώματα κτιρίων επαγγελματικών και κατοικιών.
• Βιομηχανικές εγκαταστάσεις με χαλύβδινα κουφώματα.
• Γέφυρες και διαβάσεις.
• Αρθρωτές κατασκευές και προκατασκευασμένα σχέδια.

They are the most numerous connection in a typical steel frame, which is why small savings in plate size or bolt count repeat across a job.

The calculator covers the configurations below, each suited to a different framing condition:

• Μονό πιάτο, also called a shear tab or fin plate: one plate welded to the support and bolted to the beam web. Usually the cheapest of the group, with one weld line and one bolt group.
• Double plate: plates either side of the web, where one plate cannot carry the reaction.
• Single or double angle: angles bolted or welded to the web and the support. A double angle puts the web fasteners in double shear.
• End plate: a plate welded across the beam end, then bolted to the column.
• Directly welded web: the beam web welded straight to the support, with no connecting element.

Picking between them is usually a fabrication question rather than a strength one. The reaction can be carried by any of them at the right size, so the choice comes down to access for the welder, what the erector can bolt up safely, and how much tolerance the fit-up needs.

Work through the inputs in this order:

1. Διαμόρφωση: pick single plate, διπλό πιάτο, single or double angle, τελική πλάκα, or directly welded web.
2. Μέλη: set the supported beam and the supporting column or beam, with their steel grades.
3. Connecting element: the plate or angle thickness, width and depth.
4. Φωτιστικά: βαθμός μπουλονιού, διάμετρος, τύπος τρύπας και διάταξη, or weld size and electrode strength.
5. Φορτία σχεδιασμού: the shear at the beam end, matched to the design method you selected.

Then run the design checks. Match the load to the method: LRFD takes factored loads against design strength, ASD takes service loads against allowable strength, and the calculator cannot tell which you typed.

If a check fails, the utilization ratio tells you which one and by how much. A plate limit state points at the plate thickness or depth; a bolt limit state points at the bolt count, diameter or edge distance.

Κάθε φόρμουλα, design check and code reference is shown in full, so the working can be read line by line instead of reverse-engineered from a number. That matters when the calculation has to be checked by someone who did not run it.

It also runs the detailing and clash checks before the solve, which catch the connection that satisfies every strength calculation and still cannot be fabricated or erected. Bolts that cannot be reached with a wrench do not show up in a capacity equation.

The full connection design module extends the same engine to over 80 προδιαμορφωμένους τύπους σύνδεσης, and exports 3D connection geometry directly to IFC.

• Υπολογιστής σύνδεσης Beam Splice
• Αριθμομηχανή μπουλονιών
• Σχεδιασμός Βιδωμένης Σύνδεσης
• Αριθμομηχανή σύνδεσης με βίδες
• Υπολογιστής σύνδεσης Chevron Brace
• Υπολογιστής σύνδεσης στήλης
• Υπολογιστής σύνδεσης διπλής γωνίας
• Υπολογιστής σύνδεσης τελικής πλάκας
• Υπολογιστής σύνδεσης φλάντζας
• Υπολογιστής σύνδεσης γονάτου
• Σύνδεση στιγμής
• Υπολογιστής μονής γωνίας σύνδεσης
• Υπολογιστής σύνδεσης μονής πλάκας
• SkyCiv Connection Design Vs. Στατική ιδέα
• SkyCiv Connection Design Vs. Σύνδεση Ram
• Αριθμομηχανή σύνδεσης κατακόρυφης στήριξης
• Υπολογιστής συγκόλλησης
• Σχεδιασμός Συγκολλημένης Σύνδεσης